JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

AC  Compressor: 93-97F V6 & V8 (Rebuilt)
Reviews

     This is a service replacement correct GM USA reconditioned/re-manufactured air conditioning compressor the 1993 through to 1997 & 3.4ltr V6 (up to 1995) series.

Always check the oil is in the compressor.

These come as compressor & clutch assembly (some do not)

These are a GM Delco  re-conditioned USA supplied.

They are for all intents & purposes excellent.

* This is SUPPLIED OUTRIGHT.. no deposit or exchange needed.

* This is your Delivered price when paid on line for delivery within Australia

We have  given you a clear choice, this or a NEW one.
 

 

    NOTE..Due to variable abilities & depth of training of fitters & Lack of testing or sensors or other procedures that "are a trial and error" affair..... NO WARRANTY exists on these.. not one minute.. NONE.. There is usually an outside reason the old one failed... and its STILL THERE...

     We just can't afford to take the fall for people who don't know what they are doing with them ie   a mobile re-gasser or "mate that does it" too... etc.... we State this up front as we are tied of wearing inaccurate claims to cover somebody .. remember if these were always bad GM would have a Huge world wide problem on there hands.. and not just here in Australia. There is usually an outside reason the old one failed... and its STILL THERE...

   BUT WE TRY to warn you to be 200% sure whoever does it for you.. they check all the related sensors - & KNOW how to check them..., clean out your system, use the right oil.. use the correct amount of oil, change the filter for the right GM type..not just something that fits and is cheap.. checks and double checks the system.. or you will have a buggered clutch bearing in a very short time..and the installer will ALWAYS BLAME THE PART.. so NO WARRANTY.

     YOU MUST DO IT RIGHT OR DON"T DO IT AT ALL..    This unit is a bit cheaper and GM USA sells thousands & thousands of them.... It will suit SOME people for good reasons too, especially if they are experienced and /or getting it installed by a reputable HIGHLY SPECIALISED AC Specialist..

WHICH EVER WAY YOU GO... .. for your own good....also purchase a NEW filter drying listed here at the same time.. if you do not.. your VERY VERY VERY VERY.. likely to have the new compressor spin a bearing and or seize within hours of use.

   Who ever re-gas's your system MUST.. absolutely MUST completely drain your system properly and remove all reminants of the older gas system.. otherwise again.. your going to spin the bearing and blow the money. (Picture for illustration purposes only but its the 94-95 model unit.)

 

COMPRESSOR RELATED FAILURES & CAUSES

   The following are the most frequent causes of clutch failures. These can all be traced to a problem in the compressor and/or a/c system. Please note that in nearly every case involving compressor related clutch failure, warranty is not applicable.

Seized or Slugging Compressor

The clutch’s function is to engage and disengage the compressor from the vehicle’s accessory drive system. If there is a system problem that prevents proper rotation of the compressor input shaft while the clutch is energized, the clutch will slip. A slipping clutch can generate tremendous heat, up to 1,200 degrees F. In a matter of seconds, components can start to fail. There is a progression of effects generated from slipping, all leading to overall clutch and/or compressor failure. Symptoms and causes are listed below:

  1. Loss of Lubrication:
    1. - Loss of refrigerant will also prevent oil from returning to the compressor causing binding or lockup.
      - A blockage or restriction somewhere in the system will also inhibit or prevent oil return to the compressor, thereby causing slipping, binding, or lockup.
  2. Excessive A/C System Pressure The following problems will all increase system pressure. Just as too high blood pressure causes the heart to overwork, and prematurely fail, excessive A/C system pressure can cause the compressor to overwork, begin to seize, and increase the torque requirements of the clutch. The clutch will begin to slip, which produces tremendous heat build-up. Resultant clutch and bearing failure follows.
  3. Incorrect Amount of Oil in System
    Too much oil can cause compressor slugging and a slipping clutch. Excessive oil can accumulate in the a/c condenser, increasing system discharge pressures. Not enough oil will cause compressor binding and clutch slipping.
  4. Inadequate Air Flow across the Condenser
    If the condenser is restricted internally, or has inadequate air flow across it, the result is a higher discharge pressure. This can cause the clutch to slip. Check the inlet and outlet temperatures of the condenser. A difference of over 35 degrees can indicate a problem. An inoperative or faulty radiator or condenser fan could also be suspect, or shutters not opening properly.
  5. A Blockage in the High Pressure Side of the A/C System
    A blockage will cause the discharge pressure to increase and can cause clutch slipping. A blockage in the system can usually be pinpointed by an immediate temperature (pressure) drop just following the blockage. Remember that a rise in pressure means a rise in temperature, and vice versa.
  6. System Overcharge
    An overcharged a/c system will cause pressures to increase and cause slipping. When checking for an overcharged system, remember to also check for the presence of non-condensables (air). This condition will also increase system pressures.

Leaking Compressor Shaft Seal

Another clutch failure that can be attributed to a system problem is a failed bearing due to impingement by compressor oil. This may occur if the seal on the compressor shaft leaks compressor oil, and finds it way into the clutch bearing. This oil can contaminate the bearing grease, causing it to be less effective, and also lead to grease purging through the bearing seals. The result is a gritty or failed bearing. Remember that an excessive heat condition in the system can also cause a shaft seal failure.

Mis-Machined Compressor Mounting Boss

If there is a dimensional problem with the mounting bosses used for attaching the field coil assembly to the compressor, an interface condition may be created between the field coil and rotor assembly. This problem is usually associated with poor quality re-manufactured compressors.

Re-Machined Compressor Shaft

During the course of re-manufacturing a compressor, the taper of the input shaft may be re-machined. As a result, the shaft will be shortened and less clearance will remain between the clutch and the compressor. This can create interference and hinder the rotation of the rotor assembly. Again, this problem is usually linked to poor quality re-manufacturers.

Symptoms of the preceding problems are as follows. See the illustrations below.

  1. Discolouration of Pulley and/or Armature Disc
    The extreme heat generated from slipping will quickly cause the component(s) to take on a discoloured appearance. They will appear “frosted”, or “blued”, or even charred.
  2. Melting of Rubber Spacers in Armature
    If the slipping continues, the temperature can reach a point where the rubber spacers between the armature plate and disc begin to melt. Not all clutches utilize rubber spacers.
  3. Melting of Epoxy in Field Coil
    The extreme heat can also affect the field coil, causing the epoxy to show visual signs of melting or “charring”. Under extreme situations, the coil winding will become exposed and/or unseated.
  4. Melting of Bearing Seal
    The heat will eventually cause the bearing seal to melt, allowing the grease to escape. Without grease to lubricate the bearing, it is quickly destroyed.

 


Customers who bought this product also purchased