Nov 2016.. sold out not made yet by anybody ..may be in the future but not at this time.
NOS GM # 10125293
We have very few of these left at the time of updating.. the rest have gone back / sold back to the USA.
These are not available as a Reproduction or as a genuine part.. the are fully absolutely discontinued.
This is the housing for the radio heater control assembly at the front of the console.
Genuine Pontiac Part.
NO KNOWN REPRODUCTIONS MADE as of Dec 2020.
…
SOLD .. NO MORE UNLESS YOUR PREPARED to supply your arm for it.. If really wanting a GM NOS.. try USA Ebay but be SO carefull of being either ripped off with a repro as a same number replacement ID.. or having it wrecked in transit as unless they are pack extremely well the get tossed around & cracked etc.
. GM USA on USA ebay hitting the US$300 mark .. so this is cheap and its in Australia.
This is the correct fan shroud for the PONTIAC V8.. Not the chev V8 fitted to a Pontiac ...
This is a genuine GM part.. from experience is worth the difference compared to the reproduction.
This is Genuine.. its thicker and quiet solid compared to the the reproduction.... for the 326, 350, 400 & if so fitted a 455 Pontiac V8.
As of March 2015.. we had 2 supplied out of NOS GM Stocks.. NO MORE after these are gone of GM originals new.. nice.. better.. but no more.
…
SEPT 2018 - SOLD OUT.. All went back to the USA. Few sold in Australia.
No known Repro's.
.......................
Found in our stocks Oct 2014.. we have 7 of these NOS emblems new in their GM box's for the f ront of the 1985-88 Pontiac Fiero.
…
SOLD .. 466652
Good repro's available.
Brand new ORIGINAL NOS GM Cross Flags Corvette fender emblem. Supplied individually.
Not the same as Camaro or Impala etc.. just this 3 year window of fitment only.…
NIL SOLD OUT NO MORE PROBABLY EVER NEW.
LAST OF NOS GM.. anywhere pretty much globally...
Fitted To the center of the 85-90 Firebird Trans Am
This is the last of the last of these.. not remade.. not likely too either.
It is a shown.. brand new GM original.
Red bird. GM # 16504069…
Used with INSIDE retainer clip type yoke/Universal. for the Turbo 400 / TH400/4L80 Automative box.
Used with with factory uni joints (our # PW10300)
Splines 31(in yoke) based on 32(output)
This Slip Yoke fits the Following GM Transmissions & Transfer Cases and has been in use since the 1960's:
TH / Turbo Hydromatic / Turbo 400
4l80E & 4L85E
Muncie M21 & M22
Borg Warner Super T10
(INSIDE CLIPS)
Uni is PW10300
Uni specs
Bearing Diameter A 1.125 in. (28.5mm)
Length A 2.557 in. (64.9mm)
Bearing Diameter B 1.125 in. (28.6mm)
Length B 2.557 in. (64.9mm)
…
Brand new drive shaft to Gearbox .. Turbo 350 Auto.. Yoke for 27 Spline Transmissions.
This yoke accepts 1310 series u-joints, which have 1 1/16" outside diameter cups and measure 3 7/32" wide to the outside of the cups.
The following transmissions have 27 spline output shafts:
Powerglide
Saginaw 3 Speed
Saginaw 4 Speed
Muncie 4 Speed
Borg Warner T-4
GM Borg Warner T-5
GM T-350
GM TH-350
GM T-56
700R
700R4
4L60
4L60E
4L70E
4LL0E
200 Metric
Brinn
Bert
Falcon
Yoke Features:
Spline Length: 4 1/2"
Total Length: 5 1/2" (measured from the center of the u-joint to the end of the yoke)
Accepts: 1310 Series U-Joints
1 1/16" U-Joint Cup O.D.
3 7/32" U-Joint Width (measured outside-of-cup to outside-of-cup)
External Clips
…
1969 saw another special model come out in Firebirds with a few changes that are reflected in this one year only GM workshop manual.
City phone book thick.
There is also a VERY VERY usefull "assembly manual" for 1969 Firebird available..may need to ask as they are tough to get but we will often have one.
This is NOT for the Chevy/Parisienne Series.. they have a different sub frame and drive line parts.…
Nothing gives more genuine information better then the original GM manuals... they are as thick as a city phone book and take care of electrical, mechanical and much of the body area . Its a must have to put time into a car correctly... Keep in mind too.. that in 67 GM brought out a 67 Firebird ONLY main manual suppliment that in all honesty should be brought first or in with THIS manual to get the complete manual set. This is NOT for the Chevy/Parisienne Series.. they have a different subframe and drive line parts.…
Genuine GM 1966 full Service Manual for the Bonneville Catalina / GP / GTO series. Excellent usefull tool. This is NOT for the Chevy/Parisienne Series.. they have a different subframe and drive line parts.…
Woodruff keys lock the harmonic balancer into the right position on the crank... replace it if replacing the Harmonic Balancer... GM part - this one for Olds 403 V8…
All the necessary components needed to install your original or GM Licensed repro wood steering wheel for the 1967-68 Walnut wheel or the 1969 cherrywood wheel. All the necessary parts are supplied in this - kit to completly mount the horn cap.
Note: The hub adapter is necessary for Camaros not originally equipped with wood wheel…
The front cross member.. will flex in and out.. much like the top end without a strut tower brace.. over time..
This bar its up under the front end of the 82-92 Firebird TA & Camaro and helps to maintain rigidity across the front. tension on the frame to keep the steering centered & take stress away from steering box mountings.
Easy fitment.
Delivery is covered within Australia for paid orders placed online for non bulky orders. Some NT & Regional WA locations a freight charge applies.…
New Wiring small harness, receiver and bulb kit ready retrofit, as shown.…
FITS SPECIFICALLY:
Auto console
Big or Small Block
With Console Factory gauge Cluster
** In stock normally
…
Not all wiring looms are available for the 70's range of Pontiac Engines.. this is a service only.. we can get hold of correctly removed wiringing looms from dead cars.. specific to your build.
Engine bay wiring harness..
Send your needs info at the check out please. Copy and paste this below.
Need to know:
Engine Size:
Year:
If with AC:
Distributor Type.. HEI (coil IN top of Cap) .. or Leads points style
Order as needed .. will need to come off a wreck in the USA with tools not snippers.... special order only.. may take 4 weeks.
Picture for illustration purposes only.
…
This is the engine bay wiring harness selection run.. you can have a harness that couples directly up to the factory head connector in the firewall, and runs out to the various optional and standard fittings on the V8 Range.
Choose here from the drop down menu to select the most correct series of harness you can be provided.
All come WITH the right end for factory part connection already fitted.
All come .. color matched for factory wiring schematic tracing.
When in the drop down box we ask about Air Conditioning..for Factory Gauge lights.. we are talking about FACTORY.. not aftermarket ac or some VDO gauges stuck in your car.
This is to replicate and replace worn or missing/damaged wiring properly in ONE QUICK CORRECT way..…
For the 1969 Camaro SS & Standard... only..
NOT for RS Series with the lower reverse lamps.
Full new rear harness for the rear lamp set up from the connector under the Rear parcel shelf right around lamps, includes all factory accessory leads and clips and light sockets.
Duplicates factory harness from GM exactly .
** We have too many different looms to currently list all.. there are hundreds and hundreds to figure options from - Please ask about them / quote etc..if needed also.
** USA Made
** In stock normally
…
Plastic gutter that is attached to the front of the 1969 ONLY Firewall to route the wiring over the engine... measures about 5.5 inches.…
A comprehensive schematic wiring diagram of the RS headlamp wiring & Console cluster.
Good for rebuilding and trouble shooting.
…
This connection pack is to replace the electrical wiring harness end that plugs to the Fuel Pump relay on 84-87 Corvettes. May have other uses but this is fairly specific on the loom in this vehicle which suffers from overheated loom failure.…
New GM Wiper Washer pump as shown for the 84-91 Corvette.…
Brand NEW washer pump for the washer bottle.
Fits 75-91 Corvette as original equipment.
Also Fits WHEN IN THE WASHER BOTTLE ORGINALLY >> NOT ON THE WIPER MOTOR>>
uyer's Guide : ACDELCO 86703 Windshield Washer Pump
BUICK
SKYLARK
1975-1985
CADILLAC
CIMARRON
1982-1983
CHEVROLET
CAMARO
1975-1978
CHEVROLET
CORVETTE
1976-1991
CHEVROLET
MONZA
1975-1980
CHEVROLET
NOVA
1975-1979
CHEVROLET
VEGA
1971-1977
GMC
S15 JIMMY
1983-1987
GMC
S15 PICKUP
1982-1987
PONTIAC
FIREBIRD
1975-1979
…
This is a new pair of spray nozzles or outlets for the 1967-69 Firebird & Camaro but are a pretty adaptable set with its long outlet distance from its mounting point etc if you want something for fitting to another make or model not supplied..
These fit into the plentum chamber cover and the hose from the pump connect right up to them. Supplied only in matching LH & RH pairs
…
Currect diameter hoses pre-cut to factory lengths along with installation diagram and pickup screen. Specifically for 68 & 69 Models but will fit others.…
Combined parts fitting and suiting most 60's GM Vehicles. (68 & 69 Camaro RS need additional parts)
Bracket for the resevior
Resevior that slids in
Hose Filter & Lid and hose style
Multiple hoses of routing to the wiper pump
Hoses to go to the washer outlets.
…
This is the wiper linkage built into the cowl panel.. unscrews... the wiper arms attach on each spindle to this. Currently special order.. allow 2-3 weeks for normal supply.
Fits:
68-72 El Camino
68-72 Chevelle
68-72 Monte Carlo…
At Last... the new wiper transmission linkage that goes into the cowl section for cars..most all of them.. that have the 3 bolt mount per spindle.. hidden wiper arms.. ie go down recessed behind the hood.
Delivery is covered when ordered and paid online for supply within Australia.…
Brand new.. wiper transmission assembly that screws onto the plentium chamber as original.
This is for the 67 only or 68 & 69 only Camaro & Firebird.
Comes with the wiper pivot splines and spindles... Complete for both sides as one unit.. as original.
Delivery is covered on most non bulk orders when ordered and paid on line for supply within Australia. Certain bulk and regional outback limitations apply.…
Wiper Linkage Clip Kit;
Kit contains 2 each of the following fits wiper linkage connecting the arm to wiper motor ball stud.
1-1/2" brackets,
1-1/4" brackets, screws and star washered nuts, fits wiper linkage connecting the arm to wiper motor
Used on many 60-70's GM US vehicles, both concealed and exposed wiper systems.…
Displaying 1 to 30 (of 6171 products)