These Roller vents are located under the dash on various Pontiac 60's & 70's vehicles.. mainly those with factory AC…
This is used on all Pontiac 1964-1979 factory Air conditioned cars
and 68-69 GTO hide-a-way headlight cars
and also all…
- Manufacturer
- Inline Tube
New heater blower resister located up under the dash in the heater box.
NOT FOR AIR CONDITIONED CARS.…
This is mounted on the engine bay firewall TOP of the heater box.
Image is correct.
There are a few different ones…
- Manufacturer
- OER
This is a specific AC factory resistor located in the top of the heater box on the firewall.
Its outline is…
This is the Air conditioning relay for the Camaro & Firebird, 67 & 68.. and the GM A body cars…
- Manufacturer
- AC DELCO
Relay Fan blower Motor: 68-71 Firebird TA Camaro era and other vehicles as shown.
…
This is the aftermarket receiver dryer for SOME ONLY 68-72 GM A body & full size vehicles... like…
Brand new stock of original early GM Receiver Dryers for the factory air conditioned cars.
Fits but not limited to:
…
67-79 PONTIAC 350,400,455 LOWER CRANK PULLEY - various PONTIAC applications
GM original part
Stamped code 481038YB - 8 inch or 20cm x…
- Manufacturer
- General Motors
Single belt AC pulley for the 68-72 era Pontiac GM vehicles.
mixed use.
7 3/8" x 3/8 offset (18mm)
center hole is…
This is a unique kit for Stainless Steel production parts JUST for Pontiac engines...for 69-81 Pontiac V8. All Stainless..…
Simple job lot.. these two parts often rust out around the same time.. when made in tin.
The Water pump plate…
This pipe is in the rear TOP of the head on a "PONTIAC" V8 engine (not Olds or Chevys)...…
This goes on the INSIDE of the car up on the firewall . helps limit the heat transfer into the…
- Manufacturer
- Repops USA
This goes on the INSIDE of the car up on the firewall . helps limit the heat transfer into the…
Set of original style tower hose clamps.
Good for a bit more restoration authentics when warranted.
This is a set of 8.…
Hose support Pontiac W/o AC 65-77 V8.. goes where the AC compressor would normally otherwise fit. …
- Manufacturer
- Inline Tube
Heater / Manifold / Water pump hose outlet fitting.
Often seen as the outlet that takes the heater hose out of…
Heater / Manifold / Water pump hose outlet fitting.
Often seen as the outlet that takes the heater hose out of…
Simple set of 4 hose clamps from original style remake ... for NON AC Cars.
Specifically for : *but used on…
Simple set of 6 hose clamps from original style remake ... for factory Air Conditioned Cars.
Specifically for : *but used on others
Wide…
This is the Factory fitted heater core for various A bodies and the cars listed below.. that were made…
This is the correct original fitment Heater core for 68-72 A bodies, .. ie GTO, LeMans, Chevelle, Cutlass etc..…
Brand new US Heater core as shown... at this price they are not worth repairing .
This is for a NON…
This is used inside many of the GM heater core housings.. retains the heater core into place.
Not known on…
Heater control Valve for a variety of original fitment to late 60's early 70's GM Vehicles as listed.
CHEVROLET
CAMARO
(1969 -…
This is the heater case as shown for the 66-67 GTO, LeMans, Chevelle, Malibu, Cutlass.. without factory AC.. And LH…
This is the housing used on cars that have had the factory AC system on the firewall…
Displaying 1 to 30 (of 60 products)