Bump Stop: Rear Outer 82-2002 Camaro Firebird (ea) has been added to your Cart
New GM Door Striker pin as shown for either doors on coupes or Convertible 82-92 Firebird TA & Camaro.…
This is the vented style flexible lower front spoiler for the 85-92 Camaro Iroc Z nose skin with the…
- Manufacturer
- Reproduction
This is a good viable reproduction of the NOW discontinued Camaro front spoiler. New Correct style…
- Manufacturer
- Reproduction
This is the later model rear spoiler for the 3rd gen Camaro series, adaptable to the line of 82-92…
- Manufacturer
- Reproduction
This is a full 3 peice reproduction rear spoiler based on the 82-86 Camaro series for the entire 3rd…
5 PACK ... Front and rear bumper skin and shield retainer or plastic rivet as they are also known......
Some cars…
Few of these remaining ex GM NOS Stock.
This is the small alloy cross at the brack of the mirror…
- Manufacturer
- General Motors
LHS only left in GM NOS NEW.. USA Drivers Side.
…
- Manufacturer
- General Motors
New Perfect reproduction set hood louver inserts for the Iroc series with the insert pressing already in the…
Door latch for 82-87 Camaro, Firebird & TA
These are new units to replace non existent GM latches..
LH is USA…
Original GM heavily pressed bonnet insulation pad for the 1985 thru to 90 Camaro IROC Z.. are no more.. finished..…
Reproduction partly pressed USA made and correctly outlined and strategicaly pin holed bonnet insulation pad for the 1982-82 Camaro…
Reproduction partly pressed USA made and correctly outlined and strategicaly pin holed bonnet insulation pad for the 1982-82 Camaro with…
BRAND NEW REPRODUCTON INNER FENDERS.. the plastic shaped liner for the 85-92 PONTIAC Firebird, Formula & Trans…
Brand new Fibreglass hood for the 3rd gen Camaro. Typically used on early 82-84 that had some fibreglass hoods…
A brand steel hood ... brand new.
These are U.S. sourced Reproduction hoods, previously made in Taiwain or…
- Manufacturer
- Reproduction
This is a proffessionally USA produced fibreglass re-inforced Camaro Cowl Induction hood.
It hinges and supports all…
- Manufacturer
- Custom Product
Brand New STEEL 4 inch approx 100 mm Cowl Induction bonnet / hood for the 82-92 Camaro.
Bolts to original…
Realistically possible for 3 gen Camaro hood replacement both in looks and cost.
2 inch rise, viable for the 11 mtre…
Brand New steel reproduction Stardard hood. Quality is not guarenteed..... "do they fit perfectly" ..?? probably. .is every…
This is for the additional support often needed with slightly weaker hood hinges or hood struts.
ITS NOT MEANT to take…
There is limited manufacturers of these struts.. and we know that this strut is also supplied as a OEM strut..…
THIS CLIP IS NOW DISCONTINUED.. we have NONE left.GM # was 14036396This small clip retains the hood/bonnet…
- Manufacturer
- General Motors
This is the latch . .in front of the radiator support panel.. for all the 3rd generation Firebird TA…
This is another individual part to the Camaro & Firebird TA range.. steadies the hood onto the sides of the…
Brand New Reproduction Hood hinges for the 3rd generation Firebird TA & Camaro are here at last.
Add…
This is the large plastic molded headlamp housing for the Camaro series.. the panel that stretches…
- Manufacturer
- General Motors
This is the short special boot lid strut for the Camaro and Firebird TA Convertible ONLY.
Two…
Brand New GM Ac Delco factory rear hatch strut. (ONE) really expensive but.
This is one - single genuine GM…
- Manufacturer
- AC DELCO
This is a good alternative to refit your hatch with a good aftermarket non-genuine Reproduction rear hatch strut..…
Displaying 1 to 30 (of 55 products)