Used with INSIDE retainer clip type yoke/Universal. for the Turbo 400 / TH400/4L80 Automative box.
Used with with factory uni joints…
Used with INSIDE retainer clip type yoke/Universal.
for the Turbo 400 / TH400/4L80 Automative box.
Used…
For the Harmonic Balancer needs of the Small Block Chevy.
One is one half.. = one engine needs.
You get two…
Each grommet has its metal washers and one has the earth strap...
It also kit contains the …
- Manufacturer
- OER
These oil seals fit all 1965-90 various rear end axles on disc or drum brake rear axles.
(axle seal…
Plug the hold.. goes from 47 mm to 50mm range..simply push in the hole.. do not use greasers.. and tighen…
Helping when needed.. a single size welsh plug.
These are brass unless otherwise stated.
See size list attached.…
Full Chevy Small Block V8 mainly Brass type steel welsh plus and threaded gallery plugs as shown.
General fitting 1955- 1996…
Stainless steel set of 9 main plugs and 7 small screw plugs.Picture for illustration purposes only.. all main welsh…
Black GM lid for 1963-75 GM vehicles washer bottles.
Fits Full size plus Camaro Firebird. also 63-75 Corvette.
and a squilian other…
This is a recreation of the original early washer bottle kits for the 58-64 Era Chev & other GM…
Now a complete kit made up of New GMRP parts to economically replace worn out or missing kit parts in…
- Manufacturer
- Reproduction
This is not a reproduction.
Voltage regulator for the most all US GM vehicles from 1962 to 1972...
It's a…
- Manufacturer
- AC DELCO
Nostalgic original MT valve covers used in the 60's on most every hot rodder in town...: Chev SB V8 - …
New Professionally produced small block Chevy valve covers as shown, finished in Chevy Orange.
ONE set only.
3.5 inch or 90 mm…
This is the Distributor Vacuum Advance unit mounted on the base of the early Chevy distributors.
Length from the back…
This is a wide range use vacuum Advance for the HEI Chevy Dissy from 75 & on.
…
Specific trans gasket with 13 bolt holes and one corner on 45 degrees.
IMAGE IS CORRECT.
…
If you have one of these early cast iron Powerglide Auto Transmissions.. the seal kits are different to the Alloy…
For those with the original heavy 2 speed powerglide.. this is the service pan gasket as shown.
FOR CAST IRON..…
This is the AUTO trans mount for the Alloy Powerglide.
Two hole mount form up into it from the cross member…
1962-64 Chevrolet Impala Belair & Pontiac Laurentian / Parisienne V8 w/Cast Iron Case Trans Mod Line 1pc,
Stainless…
- Manufacturer
- Inline Tube
These bring the transmisson lines together in a neat side by side line.
use as man as wanted..but normally maybe 3…
GM trans used roughly from 1980 to 83 era.. but a 3 speed auto only.
11 bolt pan as…
This kit is NOT oftern yet found on cars many drive but the 4 speed gearbox is an increasingly popular…
These are new good quality stamped chrome transmission pan for the 66+ powerglide auto box use.…
Chrome aftermarket Transmission Oil pan for the GM T-400 Auto Box.
Comes with a new oil pan bolt…
Chrome aftermarket Transmission Oil pan for the GM T-350 Auto Box.
Comes with a new oil pan bolt.
Shape is a per…
This is a part for those needing one 30 years ago were hunting.. now remade.
See the image.. its the…
Displaying 1 to 30 (of 155 products)