To help with the constant requests for information on how to rebuild and proceedures involved and parts involved inside the…
Pivot Pin Steering Column GM (1)
Used on GM vehicles for decades.
You need a pivot pin removal tool this .…
Pin, spring and retainer for use with various 67-87 era all steering columns - inc 67-9 Firebird & Camaro (with…
Power Steering cap and level for a huge range of GM PS pumps.. as early as 1963 up to…
New precise nut and washer for the 64-77 era GM power steering pump to keep the pulley on.…
- Manufacturer
- Inline Tube
Locking nut for the pulley on power steering pumps with a nut fastener.
Most all GM use it.…
Power steering ram bushing set with inserts.
One set per car.
Your choice of colors.. ..
…
- Manufacturer
- Energy Suspension
This is the steering column Heavy Duty Rubber disc that insulates the two halves of the lower intermediate steering shaft…
Power Steering Boot & Strap
JUST the dust boot and the wrap over strap.
Mainly in Aust / NZ its for 55-64…
This is the RETURN line... exactly as shown. Low Pressure hose. Can be trimmed to tighly fit whatever model..excess hose…
- Manufacturer
- Reproduction
Power Cylinder seal refurbishment kit for the 63-82 Corvette and many other 60-64 GM power steering cars..
…
This SOLID Lower Support bearing presses into the lower tube of the…
This is the basic simple Control valve seal kit for the:
Belair/Impala/Parisienne/Laurentian 1959- 64.
1965-82 Corvette …
This is for original LHD steering coupling replacement. It is the assembly as shown GM.
**** Clamp down size…
This floating bearing presses into the lower tube of the steering column and the column tube runs through it.
For…
Full brand new power steering hose, not to be confused with the Extending or retracting hose.
This is a…
New Corvette 63-82 Tie rod with the RH Thread, goes only on (if still original)
RH OUTER
LH INNER…
New Tie rod with the LH Thread, goes only on (if still original)
RH INNER & LH outer -
LH OUTER being the USA drivers side.
…
- Manufacturer
- Reproduction
Lower column rubber boot for many GM Columns from approx 1964 to 1981.
Held in by a spring clip.…
New US Moog sleeves for the Corvette tie rod ends.
Sold each.. ie two per car needed.…
For the LHD Corvette .. OR.. RHD vettes using the OEM idler arm this is it. image is correct.…
Single belt AC pulley for the 68-72 era Pontiac GM vehicles.
mixed use.
7 3/8" x 3/8 offset (18mm)
center hole is…
Mounted captive in the base of the factory steering wheel.. this spring and plastic base retainer also has the small…
Bracket Set: Power Steering SBC V8 LHS Lower Billet with mounting hardware.
This is designed to fit many castings.. comes with…
Early Corvette US LHD unaltered.. Tie rod end... LHS is USA DRIVERS SIDE.
Position of:
LH INNER
& RH Outer…
Early Corvette US LHD unaltered.. Tie rod end.
Position of:
LH OUTER
& RH INNER…
This is a full kit of 4 Power Steering hoses for the 1980-82... .. as pictured is the 80-82…
This is a full kit of 4 Power Steering hoses for the '68-79... .. as pictured is the 75-79…
New reproduction Turn Signal Switch ..in the RED/PINKISH colour .. for the 67-68 series cars with ignition…
Set of 4 .. Inner & Outer greasible early 1st gen Corvette tie rods... all 4.
Delivery is…
Displaying 1 to 30 (of 37 products)