Clips, Mounts & Retainers

Transmission Line Clip 5/16" galv. (ea)

These bring the transmisson lines together in a neat side by side line. use as man as wanted..but normally maybe 3…

Bumper Bolt: 7/16" x 1 inch (ea)

Bumper bolt, 1 inch regular  US typical 60's - 70's chrome cap headed bolt as  shown with the nut. This is…

Clip Window STUDS: 10 Pack for replacing broke studs

When the studs holding your windscreen or rear windows molding clips into place break .... your sorta stuffed as a…

Strap Wiring Retainer: 2 .75" x 1/4" (7cm x 63mm) - 10 pack

Rubber strap with push though plug ends as shown. Used on the inner mudguards of most GM vehicles in the  60's…

Locking Rod Clip (ea) - Doors

These clips hold the door lock knob rod in place. Broken or damaged clips will cause rattles…

Manufacturer

General Motors

Trim Clip Kit: 50 random design spares kit

Mixed use trim and mold plastic clip kit as shown.  Many unknown but typical spare parts clip for resto use.…

Accellerator Pedal BALL STUD: 58-70 GM various (ea)

SINGLE RESTORATION NEEDS REPLACEMENT BALL STUD for the accellerator pedal that used the Twin push on plug accelerator pad.  Best to use…

Clamps : Wire Loom Clips 3/16" (4.75mm) - 10 Pack

Securing Wiring  under the edges of mudguards, dashboards, door shells.. inner body panels, chassis stretches etc etc cleanly is the purpose…

Locking Rod retainer Anti rattle Clip (4)) - Doors

Goes from the latch along the door shell inside to retain the long rod to the shell.. ie anti rattle. …

Accelerator Pedal PIN: 67-02 GM most

Pivot pin as found on the back of the accelerator pedal.  The Spring also wraps around this. High quality general reproduction…

Manufacturer

OER

Speedo Cable Clip: 1969-81 GM

Used to hold the Speedo Cable to the shaft exitiing the speedo cluster .. holds it firm to the cluster. No…

LATCH Door SCREWS: 65-81 GM Various (6)

This phillips headed heavy duty  1/4 x 5/8" screws retain the latch to the factory door frame and into the…

Headlamp Retaining Ring Screw Kit 1940-82

Pack of 6 headlamp AF retaiing screws for a huge range of GM pre 81 (ie pre metric assembly move) for…

Starter Motor Bolt pack: (3)

This is a handy set of three starter bolts most commonly used on GM engines, each is shanked correctly…

Power steering Pump NUT & WASHER: 64-77 era GM

New precise nut and washer for the 64-77 era GM power steering pump to keep the pulley on.…

Manufacturer

Inline Tube

Bolt Kit: 30 GM AF pre metric variety pack

As shown.. at least 6 different types of AF bolts used on fenders and sheet metal. fasteners for bracket retainers…

Bell housing bolt kit: 68-72 - 6 pce

6 pce specific bolt kit for the 68-72 GM manual bell housing.…

Trim Screw Kit: 20 x 1", 20 x 3/4 " Loose washer chrome (40)

For the typical 50's- early 80's door and interior trim screws where a non cutting washer is needed on a…

Lock Rod Clip Assorted: Door Area

This small kit may help restorers trying put the locking rods and handle interal rod linkages back together. It…

Shim Kit: 50 pce Auto shims

This is a pack of  50 shims..  - wides pread different types and thickness's of the main popular…

Manufacturer

PWD

Bush: Corvette T-Top Alignment 68-82 (4)

Four of the small cone shaped inserts.  …

Bolt kit: 20 Pce - 10 x 3/8" & 10 J Nuts

Bolt kit: 20 Pce - 10 x 3/8" Bolts + 10 "J Nuts." Found on SO SO MANY GM…

Bolt Kit: 20 Pce - 10 x 5/16-18 & 10 x U bolts w/ Blunt End bolts

This is  a pack of 20 piece PACK of  useful new GM style BLUNT END / FLAT END bolts and…

Gearbox Mount: 57-76 GM various

Brand new Rubber gearbox mount for the first gen Camaro & Firebird as listed below, fits a wide variety of year…

Clip Kit Door Trim 64-74 (12)

Small parts kit for the fastening of the door trims to most GM Vehicles that used a metal press though…

Heater Hose BRACKET SET (2)

Used for over 50 years on various GM Vehicles.. this is ONE PAIR of heater hose brackets that fit on…

Manufacturer

OER

Heater Hose CLAMP for A/C 64-79 GM cars (6)

Simple set of 6 hose clamps from original style remake ... for factory Air Conditioned Cars. Specifically for : *but used on others Wide…

Bolts: Smaller head access bolts (12) 3/8" x 16x1

For accessing tighter locations.. 3/8" af bolts.. in black.. Hex Head Used on various areas including hedders..  12 in the kit…

Trailing Arm Stud set: Corvette 65-82 (4)

New set of 4 high tensile Corvette rear trailing arm bolts and nuts.. or STUDS... as shown.…

T-Top Center Spade: Corvette 68-82 (ea)

Chrome center spade support for the 68-81  Corvette as shown, pushes into the alignment housings. Supplied each Heavy duty Chrome. SHIMS also available..…