Often folk call up and ask us to research paint codes.. where to get them .. who locally…
Just for a general insight.... This really only concerns Bigger panels, bonnets, doors.. mainly external / dress…
Bumper bolt, 1 inch regular US typical 60's - 70's chrome cap headed bolt as shown with the nut.
This is…
These oval metal plugs replace the damaged or missing plugs?in your Camaro floor pan & boot area.
There is also…
Rusty or corroded trays are common after 30 odd years of use.. these are perfectly pressed and easy to fit.
Correct…
- Manufacturer
- OER
Brand new tough to get brace skirt for the 67-9 Camaro & 67-9 Firebird TA.
Supplied EACH
LHS is…
When replacing the floor on the rear of any '67-9 Camaro & Firebird... these rear seat supports are needed normally…
This is a handy 100 piece bolt kit for wide use on most 64-72 era GM U.S. Vehicles. It's…
These are the bolt on panel at the front lower section of the front fender.
Reproduction part, works with both repro…
This is an ABS front spoiler ONLY ..not brackets or bolts etc.. for the 67 & 68 Camaro…
- Manufacturer
- OER
These are SO easy to be damaged in transit.. Each one has to have a HD box built for…
- Manufacturer
- OER
This is what the roof gutter mold clips onto AT THE FRONT A PILLAR.. seen on the inside up under…
Thankfully the quality choices of these has improved over the last 4-5 years and production costs are very…
- Manufacturer
- Reproduction
For the repair assistance on subframes where splits and wear deminishes the strength of the mounting support holes.
These…
This is as shown... a comprehensive kit includes most of the correct fasteners which are required to mount the front…
- Manufacturer
- OER
Good reproduction, just as good as the GM unit... from experience...... and NOT a cheap second.
Freight…
- Manufacturer
- Reproduction
This shorter rear deck panel goes between the rear quarter panels, is used for repairing rusted deck area's…
- Manufacturer
- Reproduction
Front of floor under the pedal area on the 67-9 Camaro or Firebird.
LHS is USA Drivers Side.
Sold EACH
Delivery additional…
This is a upgraded design of the previously fairly week replacement that was around.
It is designed to keep…
- Manufacturer
- Reproduction
There are a few varieties of these.. not every "trunk floor" or boot floor is the same pressing or…
- Manufacturer
- Reproduction
This panel is a common rust area. The repro is correct in every way... and is a perfect replacement…
- Manufacturer
- Remanufactured (USA)
This 68 ONLY panel replaces the difficult to duplicate and now unfortunately all too often in major restorations on…
- Manufacturer
- Reproduction
.. These panels extend from the front edge of the floor pan up to the firewall ..basically under the…
There is a couple of these now out on the market, this is the bit heavier one.. good sharp…
- Manufacturer
- Reproduction
New Steel INNER rocker panels for the 67-9 F COUPE.
Choose the side you need.. all are as per factory fit...…
- Manufacturer
- Reproduction
This kit give you virtually every bolt, washer, nut and fastener you will need ... including the washer head pointed…
Full Floor panel for the RHS of the 67-69 Firebird or Camaro. Normal Taiwanese pressings.. good for the…
NO LONGER SUPPLIED unless ordered...: ... just not worth the freight cost and agravation from some users for such a bulky…
- Manufacturer
- Reproduction
These are the top out sections constructed.. they replace the section next to the hood hinge area... on the…
- Manufacturer
- Reproduction
This is the factory style pressing of the outer rocker panel for replacement use on either LH or RHS as…
- Manufacturer
- Reproduction
Displaying 1 to 30 (of 72 products)