This is the roof cover material presewn, heat sealed Levant material design known to be used originally on the 70-74…
Rear interior UPPER side trim panel.
. LH or RH sides.
Reproduction Part. Trim Panel: fits only 1975-81F
1975-81 Firebird TA…
Reproduction Part.
THIS IS A PAIR SET, for cars with molded headlining.. not bows.
for specifically 1973 models with molded headlining…
THIS IS A REPRODUCTION PART, black in color.
These are supplied individualy.
and a choice of colour being .. Black…
THIS IS A REPRODUCTION PART, black in color only,..paint to match the many colors other then black.
1971-72 Firebird…
This is the main kit if you have GM T-Tops on a 1978-81 Camaro Firebird T-Tops that…
78-81 Camaro Firebird T-Tops that are GM have these plastic molding end caps on all interior opening outer corners but…
These are the front outer GM T-Top latch plastic trim moldings as shown.
Supplied in matched pairs.. in…
This is a newly produced T-top "Y" section for the 78-81 Firebird TA & Camaro.
They go on the LH &…
Single handle on each t-top is what to look for 1st as there are more then a few brands of…
- Manufacturer
- OER
This is a PAIR of perfect reproduction sunvisors for the 1974-81 Series Firebird TA & Camaro... they are soft vinyl…
- Manufacturer
- PUI
New sunvisor have been needed for quite a while for the 2nd gens.. now they are and very reasonable cost…
This is a PAIR of perfect reproduction sunvisors for the 1970 Series Firebird TA & Camaro... they are soft…
- Manufacturer
- Reproduction
New sunvisor brackets have been needed for quite a while for the 2nd gens.. now they are and very…
Located above your shoulder on the outer side.. holds the sholder belt and buckle for those with the factory splits…
The correct screw kit for both sides (IE one car) interior pillar post moldings
on 70-81 Camaro…
This is for all 70-81 Model Firebird, Trans Am & Camaro.
This is the dye cut cardboard rear shelf trim panel…
For all 70-81 Model Firebird Trans Am & Camaro.
This is the Deluxe dye cut cardboard rear shelf trim panel…
This is the factory deluxe optional
MAP READING LIGHT LENS
+
the Chrome diecast housing.. nothing more.
Found on a lot of…
USA made correct interior roof mounted center light wiring loom with retainers per original.
Fits the type of bulk that has…
Round interior lense with the sunburst inprint...
Fits heaps of GM cars from around 1968- 86…
- Manufacturer
- OER
Round plastic silver housing for the interior light lens.
Screws to the roof cross-brace.
Perfect reproduction.
…
- Manufacturer
- OER
The people who experience LED lighting especially for tail lamps, like this also for the INTERIOR replacement Bulb..Its twin pin as…
Special order only .. allow 2 -4 weeks depending on USA ready supplies ex manufacturer.
This…
- Manufacturer
- Flatline Barriers
This is a material headliner.. kit.. designed to replace those polystyrene / cardboard headliners.. It is a material headliner.. the…
Headliner for the 74-81 in plastic injected molded one piece. This is not fall apart like the polystyrene ones. It…
- Manufacturer
- Reproduction
This is the kit needed for the headliner plastic side trim strips.. often missing or oxidized to buggery and unstable.
Comes…
Headliner side trim molding hardware retainer set for the 70-74 Camaro or Firebird TA.
…
This is the headliner SIDE trim for the 74-81 Firebird Camaro.
This is a pair .. any BLACK colour you like…
These plastic "Christmas Tree Clips" are used to hold the plastic side interior trim mould into place.. self retaining.
Takes about…
Displaying 1 to 30 (of 36 products)