For 67-68 or 1969 Models.. Choose...
This is the OUTER REAR Wheelhouse from the center of the rear wheel…
- Manufacturer
- Reproduction
This panel will replace the factory inner wheel well panels on your Camaro.
This is a superb quality restoration reproduction…
- Manufacturer
- Reproduction
There are a few varieties of these.. not every "trunk floor" or boot floor is the same pressing or…
- Manufacturer
- Reproduction
Front of floor under the pedal area on the 67-9 Camaro or Firebird.
LHS is USA Drivers Side.
Sold EACH
Delivery additional…
This is the factory style pressing of the outer rocker panel for replacement use on either LH or RHS as…
- Manufacturer
- Reproduction
New Steel INNER rocker panels for the 67-9 F CONVERTIBLE, these are much more expensive then a coupe.. but…
- Manufacturer
- Reproduction
New Steel INNER rocker panels for the 67-9 F COUPE.
Choose the side you need.. all are as per factory fit...…
- Manufacturer
- Reproduction
The most complete rear deck panel for rebuilding the:
67-9 Camaro or Firebird Coupe or Convertible.
Comes with the main hinges.. deck…
This is the full CONVERTIBLE ONLY rear panel..
HINGED for the trunk lid.. includes mounts and tension…
- Manufacturer
- Reproduction
There is a couple of these now out on the market, this is the bit heavier one.. good sharp…
- Manufacturer
- Reproduction
This shorter rear deck panel goes between the rear quarter panels, is used for repairing rusted deck area's…
- Manufacturer
- Reproduction
This patch is designed for easy installation with original wheel well lip shape the patch is approximately 27 cms by…
- Manufacturer
- Reproduction
These are a special skin designed to help repair rusted or damaged wheel arches and the face area of a…
- Manufacturer
- Reproduction
These oval metal plugs replace the damaged or missing plugs?in your Camaro floor pan & boot area.
There is also…
These are under the front seat floor pans and form the structural reinforcment to mount the seats runners.
LH is USA…
These are under the front seat floor pans and form the structural reinforcement to mount the seats runners.
LH is USA…
These are for 68-69 Firebird & Camaro's... they are the full replacement rear frame rail.. as it would be…
- Manufacturer
- Reproduction
Full Floor panel for the RHS of the 67-69 Firebird or Camaro. Normal Taiwanese pressings.. good for the…
Type One of this panel.. has more going up the sides and the main guts of the floor needed.. with…
- Manufacturer
- Reproduction
Type Two of this panel.. better suited for many rust fixing applications.
This is a factory replicated sectional pressing for the…
This panel is the ideal replacement part if only your rear floor sections under where you put your feet...…
- Manufacturer
- Reproduction
Each 1967-69 panel extends from the rear seat section to the firewall extension upward near the transmission tunnel.
Each…
- Manufacturer
- Reproduction
These bulky new parts are available as either a left or right hand unit and are an excellent alternative to…
- Manufacturer
- Reproduction
These are the front floor sections that run between the flat of the floor pan to the vertical flat of…
- Manufacturer
- Reproduction
This is the FULL floor panel for the 67-69 Camaro & Firebird Convertible.. and will fit on the Coupe version…
This is what the roof gutter mold clips onto.. this is the metal gutter..
It is the…
This is the very lower outer repair patch . supplied for the 69 Firebird or Camaro. It's noted as…
Its the upper exterior panel that needs that is the upper cowl panel. where the vents are.
This panel takes the…
- Manufacturer
- Reproduction
These are for repairs needing more then the thin outer wall skins.. These lip over the top…
- Manufacturer
- Goodmark Industries
This patch is designed for easy installation with original wheel well lip shape the patch is approximately 27 cms by…
- Manufacturer
- Reproduction
Displaying 1 to 30 (of 33 products)