These oval metal plugs replace the damaged or missing plugs?in your Camaro floor pan & boot area.
There is also…
Type Two of this panel.. better suited for many rust fixing applications.
This is a factory replicated sectional pressing for the…
For 67-68 or 1969 Models.. Choose...
This is the OUTER REAR Wheelhouse from the center of the rear wheel…
- Manufacturer
- Reproduction
This is the lower front section of the rear 1/4 panel. Precision stamped panel ready for fitment.
Comes in any…
This is what the roof gutter mold clips onto.. this is the metal gutter..
It is the…
This Rear of Rear patch is designed for easy installation with original wheel well lip shape.
The metal correctly shaped …
- Manufacturer
- Reproduction
This shorter rear deck panel goes between the rear quarter panels, is used for repairing rusted deck area's…
- Manufacturer
- Reproduction
These are under the front seat floor pans and form the structural reinforcement to mount the seats runners.
LH is USA…
These are under the front seat floor pans and form the structural reinforcment to mount the seats runners.
LH is USA…
This panel will replace the factory inner wheel well panels on your Camaro.
This is a superb quality restoration reproduction…
- Manufacturer
- Reproduction
Front of floor under the pedal area on the 67-9 Camaro or Firebird.
LHS is USA Drivers Side.
Sold EACH
Delivery additional…
The lower rear section of each front mudguard / fender is reproduced here enabling easier cut & replace restoration…
- Manufacturer
- Reproduction
This patch is designed for easy installation with original wheel well lip shape the patch is approximately 27 cms by…
- Manufacturer
- Reproduction
There are a few varieties of these.. not every "trunk floor" or boot floor is the same pressing or…
- Manufacturer
- Reproduction
This is the very lower outer repair patch . supplied for the 69 Firebird or Camaro. It's noted as…
This patch is designed for easy installation with original wheel well lip shape the patch is approximately 27 cms by…
- Manufacturer
- Reproduction
These bulky new parts are available as either a left or right hand unit and are an excellent alternative to…
- Manufacturer
- Reproduction
This panel is the ideal replacement part if only your rear floor sections under where you put your feet...…
- Manufacturer
- Reproduction
There is a couple of these now out on the market, this is the bit heavier one.. good sharp…
- Manufacturer
- Reproduction
These are the front floor sections that run between the flat of the floor pan to the vertical flat of…
- Manufacturer
- Reproduction
New Steel INNER rocker panels for the 67-9 F COUPE.
Choose the side you need.. all are as per factory fit...…
- Manufacturer
- Reproduction
Full Floor panel for the RHS of the 67-69 Firebird or Camaro. Normal Taiwanese pressings.. good for the…
This is the factory style pressing of the outer rocker panel for replacement use on either LH or RHS as…
- Manufacturer
- Reproduction
Type One of this panel.. has more going up the sides and the main guts of the floor needed.. with…
- Manufacturer
- Reproduction
Each 1967-69 panel extends from the rear seat section to the firewall extension upward near the transmission tunnel.
Each…
- Manufacturer
- Reproduction
These are for 68-69 Firebird & Camaro's... they are the full replacement rear frame rail.. as it would be…
- Manufacturer
- Reproduction
These are a special skin designed to help repair rusted or damaged wheel arches and the face area of a…
- Manufacturer
- Reproduction
The most complete rear deck panel for rebuilding the:
67-9 Camaro or Firebird Coupe or Convertible.
Comes with the main hinges.. deck…
New Steel INNER rocker panels for the 67-9 F CONVERTIBLE, these are much more expensive then a coupe.. but…
- Manufacturer
- Reproduction
Its the upper exterior panel that needs that is the upper cowl panel. where the vents are.
This panel takes the…
- Manufacturer
- Reproduction
Displaying 1 to 30 (of 33 products)