Grommet and sleeve kit that installs where the accelerator rod fits into linkage.
…
Supplied here as a plug in set. socket & globe.
Note this is the typical 50-80's 1/2 inch socket.
…
Glove Box Door Bump Stops.
The correct pair of rubbers for the job.
Sold as a pair.
Used from late 1930's to early…
Pair of economy version chrome PLASTIC door pull knobs.
NOT METAL..
THESE HAVE THE DOMMED INWARD top.. NOT raised like post 67.
Used…
Used on seat trim to strap trim edges tight. .known as hog rings..
50 pack as shown.…
Pivot pin as found on the back of the accelerator pedal. The Spring also wraps around this.
High quality general reproduction…
- Manufacturer
- OER
Pair of the softer thick gasket on the back of the inner door handles for the GM A body series.
Supplied…
Brake and cluch pedal thin specific shaft bushes as found on most all GM USA vehicles 65-81 era.
Set of 4.…
Pair thin radio nuts for the majority of factory radios in the 60 & 70's as shown…
Used to hold the Speedo Cable to the shaft exitiing the speedo cluster .. holds it firm to the cluster.
No…
High quality general reproduction accelerator pedal PAD
Fits most all GM from 67-2002.
67-02 Firebird & Camaro,
68-82 Corvette
72-75 Impala / Caprice
68-79 Nova
68-77 Pontiac…
- Manufacturer
- OER
This is a Pair - Plastic door lock knobs that are produced as per…
Speedo Cable hole rubber plug.. for filling the hole left .. grommet size ok for most every know speedo cable…
Seals the flange plate at the interior of the steering column where it attaches to the firewall and helps prevent…
- Manufacturer
- Inline Tube
These are the chrome handle with BLACK knob for standard interiors... .
This is currently also available in original GM at…
- Manufacturer
- Reproduction
This is the chrome threaded nut that goes around the various 66-67 Ignition locks on the dash mounted switch/lock combination.
This…
- Manufacturer
- OER
For the typical 50's- early 80's door and interior trim screws where a non cutting washer is needed on a…
High quality general reproduction accelerator pedal PAD &
Trim bezel Set for those that simply want both.
Suits ALL 1968-81 A B…
These service parts door lock knob ferrules are finished in a chrome plated metal finish.
Fit most 68-81 GM Vehicle…
Rectangular centered interior light lens.
Excellent Reproduction supplied.. ...
Fits many 68-70 US GM Vehicles inc GTO/LeMans / Tempest, Chevy Chevelle/…
- Manufacturer
- Goodmark Industries
Nice real metal chrome plated coat hook for the early cars.. 55-68 era..
Pair as shown.…
The sunvisor's on most 64- 72 era GM vehicles.. except convertibles.. the factory sunsisors pivot on one of…
- Manufacturer
- OER
New Correct reproduction tilt lever for the majority of GM needs. from 68 to 88.…
Set of two springs as shown.. used on but not limited too..
67-69 Firebird
67-69 Camaro
67-68 Chevelle / Malibu
67 Impala
67-72 Olds…
1966-77 GM Automatic Transmission Brake Pedal bracket swing arm mounting kit with bushes as shown.…
- Manufacturer
- Inline Tube
Rather then yanking on the steering wheel and bending the crap out of it... use a puller and it…
Simple trade style tool make tucking the head liner into the tight gap opening up the side particularly quite…
USA made set of the watershields for a 68 to 72 Chevelle or Malibu Coupe, plust GTO, and 69-72 Pontiac…
- Manufacturer
- Repops USA
These are the Headliner Clips used on (but not limited too) 68 - 72 GM Impala, Chevelle, Cutlass, Nova around the…
- Manufacturer
- General Motors
Small but vital accellorator pad support for the 2nd gen F bodies.. 70-81 Firebird TA & Camaro.…
Displaying 1 to 30 (of 72 products)