Factory exhaust manifold bolt and bolt/studs in a 6 pack as shown.…
Brand new tough to get brace skirt for the 67-9 Camaro & 67-9 Firebird TA.
Supplied EACH
LHS is…
Fuel and Brake Line Clip Set SUITS APPLICATIONS USING DUAL LINES 3/8" and 1/4"
7 Piece Set…
Clip Set - 10.
Full set of clips to suit all 68 & 69 Camaro coupe & convertible models with drum…
Round boot lid bump stop .. used on heaps of 60's vehiceles ... including but not limited too..
67-9 Camaro &…
Hood bump stops are used on most all GM vehicles. this one may be used as a pair or 4…
- Manufacturer
- OER
Larger of the common two pin bump stops.. shown and size in the image.
This is ONE ONLY.. (1)
Used on…
This 10 piece kit does both front and rear of the 1967 Camaro only (not 68 or 69).. each chrome…
- Manufacturer
- Reproduction
Front and rear chrome headed bumper bolt set of 10 .. as needed for the 68 or 69 Camaro.
Not for…
- Manufacturer
- Reproduction
This is the 4 specific bolts and hardware for mounting the front 69 Camaro outer insulator supporting brackets.…
Bumper bolt, 1 inch regular US typical 60's - 70's chrome cap headed bolt as shown with the nut.
This is…
Front. This kit is highly recommended when replacing your front bumper after an accident.
These bolts do become stressed over…
Front Bolt Kit for the 67-69 era GM Camaro, Nova, various Chevelle.
... This kit is highly recommended when replacing your…
Brake and cluch pedal thin specific shaft bushes as found on most all GM USA vehicles 65-81 era.
Set of 4.…
This is the correct black screws for the Headlamp doors for the 67-68 Camaro.
One kit one car.…
These keep the chrome moulding attached to the body. Set of 10 is used to replace all.
This IS a set…
- Manufacturer
- OER
Fuel line pipe clamp (11 mm o/d & for pipe of original 3/8th o/d) - GREEN…
- Manufacturer
- General Motors
Five different sizes and strengths for the restoration needs on most US GM Vehicles will be met with this 50…
Securing Wiring under the edges of mudguards, dashboards, door shells.. inner body panels, chassis stretches etc etc cleanly is the purpose…
50 piece vacuum/fuel hose spring clamp kit with these assorted sizes listed below.
Fits many needs on GM vehicles between 1960-1990.
Sizes Included:…
Small parts kit for the fastening of the door trims to most GM Vehicles that used a metal press though…
Door trim METAL clips and cone round fastener pack of 24.
As shown.
fits various 1958-81 GM vehicles.
Suits:
…
Complete door and sill mold clip kit for the 1968 Camaro with the RS Lower Side mold option. …
- Manufacturer
- Reproduction
Windscreen Clip kit for the 67-69 Camaro and Firebird & Many others.. this is the upper sides and top set.
SET…
This is the Rear window glass clip kit for Various specific GM cars. Its a 24 clip kit.
Does all 4…
This is the full set of lower front windscreen molding clips for the 67-9F.. including the outers and the…
Usefull tool kit set for working most all clips and retainers on GM & Ford cars of the 50's…
When the studs holding your windscreen or rear windows molding clips into place break .... your sorta stuffed as a…
On the lower outer side of the front windscreen molding.. just on the outer section.. these clips are located…
- Manufacturer
- OER
Correct base rivet retainers with generic bolts and washers as factory engineered for the floor console mounting on 68-9 Camaro.…
- Manufacturer
- OER
Displaying 31 to 60 (of 149 products)