Small parts kit for the fastening of the door trims to most GM Vehicles that used a metal press though…
Door trim METAL clips and cone round fastener pack of 24.
As shown.
fits various 1958-81 GM vehicles.
Suits:
…
Usefull tool kit set for working most all clips and retainers on GM & Ford cars of the 50's…
When the studs holding your windscreen or rear windows molding clips into place break .... your sorta stuffed as a…
Headliner mounted coat hook.
Available in Henry Fords favorite Colour.
These are found on …
For the 79, 80 & 81 Dash Pad on the Camaro series ONLY.
Supplied as a pair.. you use two a…
This is the peice shown for the inner lock rod 2 part rod and clip set .
Supplied PER DOOR. Order…
- Manufacturer
- OER
Set of 6 plastic clips for the use on the outer door molding.. where factory fitted.. to any 70-81…
So often lost .. comes with the nut also as show
TWO per door window
Fitted to the end of the main tracks…
Type TWO.. TALL & NARROW - the typical Performance Mount for Chev V8 Mount
ONE MOUNT ONLY - Order Two for one…
- Manufacturer
- Energy Suspension
RUBBER
Pull away locking type engine mount for Chevy small Block.. Best value and better product too.
Fits most 66-72…
Brand new Rubber gearbox mount for the first gen Camaro & Firebird as listed below, fits a wide variety of year…
Manual gearbox mount for the 93 Firebird & 93-97 Camaro V6.
NOT for V8 or Automatics
These look similiar…
Glove Box Door Bump Stops.
The correct pair of rubbers for the job.
Sold as a pair.
Used from late 1930's to early…
Correct Enginetech Tensile Chevy small block engine bolts...
- 1955-2000.
Enginetech Head Bolts are made to…
Used on most all 1st gen F & many 70-82 2nd gens..
Four required per car for a complete set and…
- Manufacturer
- General Motors
Set of 6 small retainers and screws for the headlamp chrome bezel retaining in the 70-73 Camaro.
ONE set per vehicle.…
Headlamp bucket adjuster spring.
order as needed.…
Pack of 6 headlamp AF retaiing screws for a huge range of GM pre 81 (ie pre metric assembly move)
for…
Used for over 50 years on various GM Vehicles.. this is ONE PAIR of heater hose brackets that fit on…
- Manufacturer
- OER
Simple set of 6 hose clamps from original style remake ... for factory Air Conditioned Cars.
Specifically for : *but used on others
Wide…
Used on seat trim to strap trim edges tight. .known as hog rings..
50 pack as shown.…
Usually 4 of these fitted 2 each side of the bonnet to limit…
Set kit of 8 loose washer headed bolts.
Kit of 4 each side.. not you may receive flat or pointed headed…
This is for the additional support often needed with slightly weaker hood hinges or hood struts.
ITS NOT MEANT to take…
Male To 3/8-24 Female Sae Hose Line Fitting Adapter For 3/16
mainly for hydraulic hose line adaption. power steering systems.…
Hardware Door Inner Mounting set 70-81 Camaro & Firebird TA.
Each…
This is a correct GM style replacement part to hold your lock cylinder in place inside the door shell... slides…
This clip as pictured.. mounts to the door shell and retains the locking rods from rattling away or sag etc.
Supplied…
This is for the regular bullet mirror as found on the 70-81 Camaro & Firebird TA
Choose LH (USA drivers) or…
Displaying 31 to 60 (of 90 products)