New reproduction Turn Signal Switch ..in the RED/PINKISH colour .. for the 67-68 series cars with ignition…
New US Moog sleeves for the Corvette tie rod ends.
Sold each.. ie two per car needed.…
New Tie rod with the LH Thread, goes only on (if still original)
RH INNER & LH outer -
LH OUTER being the USA drivers side.
…
- Manufacturer
- Reproduction
New Corvette 63-82 Tie rod with the RH Thread, goes only on (if still original)
RH OUTER
LH INNER…
Early Corvette US LHD unaltered.. Tie rod end.
Position of:
LH OUTER
& RH INNER…
Early Corvette US LHD unaltered.. Tie rod end... LHS is USA DRIVERS SIDE.
Position of:
LH INNER
& RH Outer…
Set of 4 .. Inner & Outer greasible early 1st gen Corvette tie rods... all 4.
Delivery is…
Pin, spring and retainer for use with various 67-87 era all steering columns - inc 67-9 Firebird & Camaro (with…
This SOLID Lower Support bearing presses into the lower tube of the…
This floating bearing presses into the lower tube of the steering column and the column tube runs through it.
For…
To help with the constant requests for information on how to rebuild and proceedures involved and parts involved inside the…
US Remanufactured 16.1 ratio Steering box for the 69-82 model.
Note the housing is shorter then the other box type.
No Exchange…
Single belt AC pulley for the 68-72 era Pontiac GM vehicles.
mixed use.
7 3/8" x 3/8 offset (18mm)
center hole is…
Power steering ram bushing set with inserts.
One set per car.
Your choice of colors.. ..
…
- Manufacturer
- Energy Suspension
As new USA remanufactured Corvette power steering pump for the 1982 Corvette only.
No Exchange needed.
…
- Manufacturer
- Remanufactured (USA)
USA Remanufactured complete power steering pump the genuine replacement on 1980 & 81 Corvette.
No exchange needed.…
- Manufacturer
- Remanufactured (USA)
As new USA remanufactured power steering pump with resevior pr the 75-79 Corvette, complete ready to bolt on and…
- Manufacturer
- Remanufactured (USA)
As new USA remanufactured power steering pump with resevior pr the 63-74 Corvette, complete ready to bolt on and…
New precise nut and washer for the 64-77 era GM power steering pump to keep the pulley on.…
- Manufacturer
- Inline Tube
Power Steering cap and level for a huge range of GM PS pumps.. as early as 1963 up to…
This is the RETURN line... exactly as shown. Low Pressure hose. Can be trimmed to tighly fit whatever model..excess hose…
- Manufacturer
- Reproduction
Full brand new power steering hose, not to be confused with the Extending or retracting hose.
This is a…
This is a full kit of 4 Power Steering hoses for the 1980-82... .. as pictured is the 80-82…
This is a full kit of 4 Power Steering hoses for the '68-79... .. as pictured is the 75-79…
We will not supply these to people who don't get this part fitted proffessionally.. as its not straight forward. Dirt…
Power Steering Boot & Strap
JUST the dust boot and the wrap over strap.
Mainly in Aust / NZ its for 55-64…
Power Cylinder seal refurbishment kit for the 63-82 Corvette and many other 60-64 GM power steering cars..
…
Power Steering Power Cylinder assembly as shown. Direct factory replacement, fit and forget.
BRAND NEW ONLY.. no more cheap…
- Manufacturer
- Remanufactured (USA)
Pivot Pin Steering Column GM (1)
Used on GM vehicles for decades.
You need a pivot pin removal tool this .…
Locking nut for the pulley on power steering pumps with a nut fastener.
Most all GM use it.…
Displaying 1 to 30 (of 37 products)