Side rod clamp kit - 10 inch J type.. with fasteners.
Make sure you check clearance before closing bonnets etc..
Trim rods…
Most every battery tray uses one of these to clamp the battery securely.
This is black as shown. A Chrome BRACKET…
This is a mounting bracket for Alternators.. primarily in the 60's era that will allow the mounting to the…
Red positive battery power lead with bolt up clamp as shown.
Only
This is a bit over 5 feet long or 160Cm...
General…
This is the manifold mounted coil bracket for most applications from late 50's to mid 80's.
Note the bracket…
Original restorations of 50-'s to early 70's GM V8 used this specific bracket heaps.. with it being at restoration…
This is for CHEV V8 with YELLOW BLACK & RED wire..
This is a GM Ac Delco.. …
- Manufacturer
- AC DELCO
This is for Pontiac & Olds V8 (and later 80's Corvettes ONLY w/ CHEV V8 with)
WHITE, BLACK…
- Manufacturer
- AC DELCO
This is the wiring shown.. sometimes found just missing or melted.
Two blade terminal connector - as shown.. so check if…
- Manufacturer
- Reproduction
This is the Alternator Connector for most early 60's to later 70's GM Ac Delco units.. Two stacked splade encased…
For those wanting a functional Cowl Induction Solonoid activated flapper door set up on the Camaro style CI bonnet..…
Functional Hood Solinoid for the Cowl induction on 69-76 Corvette, Camaro and some TA's…
Cap + Rotor... for points style pre-73 dissy
This is for the standard Distributor used on Pontiac and Chev V8s from…
Brand New GM Delco dissy cap and rotor for the HEI 74-84 & newer "Coil in the cap"…
- Manufacturer
- AC DELCO
New Distibutor CAP for the standard points dissy on GM V8's from 58-73. NOT for HEI or aftermarket dual…
Chrome distributor clamp and bolt for most GM engine post 63.…
- Manufacturer
- Custom Product
Brand new billet alloy HEI COMPLETE distributor for the Chevy SB & BB applications. These are Chinese Built.. we have…
- Manufacturer
- Custom Product
This is the housing used on cars that have had the factory AC system on the firewall…
Specifically made for 1958-96 GM massively wide use... set of correct metal horns with brackets.. with correct alternate notes.. as per…
Specifically made for 1969 Camaro only.. set of horns with brackets.. with correct alternate notes.. as per image correct. This…
- Manufacturer
- GM Restoration Part Approved
A replacement part.
NOT for 69-70 Firebird with NON tilt column.
Not to be confused with the ignition barrel and lock.
This part is 1/2…
A correct reproduction part to suit all cars fitted with Turbo 400 Transmission and center console.
Picture is correct & its…
- Manufacturer
- OER
For the 4 speed Manual transmissions correctly set up with a neutral safety switch on the outside of the box.
Suited…
This is for the Camaro when fitted with a Turbo 350 or Powerglide 2 speed and console in the…
- Manufacturer
- OER
This is the OIL PRESSURE SWITCH / SENSOR UNIT..... .. this is for cars with dashboard LIGHTS not the…
- Manufacturer
- AC DELCO
New series points and condensor set for pretty much every American GM V8.
Fots
…
Improved older Points set for standard GM Chevy / Pontiac V8 style distributors.
It does not include a condensor ..…
Blower motor relay for the 67-9 Firebird & Camaro..& 65 thru to 72 GTO/LeMans/Cutlass/Chevelle & other 60's uses. …
- Manufacturer
- Reproduction
This is mounted on the engine bay firewall TOP of the heater box.
Image is correct.
There are a few different ones…
- Manufacturer
- OER
In 1968 Camaro's with the accessory Console Gauge Cluster used this specific temp sensor... NOT 1967 or 1969.. just…
- Manufacturer
- Reproduction
Displaying 1 to 30 (of 47 products)