For 67-68 or 1969 Models.. Choose...
This is the OUTER REAR Wheelhouse from the center of the rear wheel…
- Manufacturer
- Reproduction
This panel will replace the factory inner wheel well panels on your Camaro.
This is a superb quality restoration reproduction…
- Manufacturer
- Reproduction
This panel usually rusts in any make of vehicle with time.
They join to the lower section of the…
- Manufacturer
- Reproduction
This is the 3 pieces used to repair the rusted weather seal channels.
Very useful kit and good value…
- Manufacturer
- Reproduction
Have a look at the 1969 ONLY panel... it is designed to fix rusty floor center area's s…
- Manufacturer
- Reproduction
Choose from either complete section 1967 or 68 models only panels... it is designed to fix rusty floors or damaged…
- Manufacturer
- Reproduction
There are a few varieties of these.. not every "trunk floor" or boot floor is the same pressing or…
- Manufacturer
- Reproduction
For the repair assistance on subframes where splits and wear deminishes the strength of the mounting support holes.
These…
This is the factory style pressing of the outer rocker panel for replacement use on either LH or RHS as…
- Manufacturer
- Reproduction
New Steel INNER rocker panels for the 67-9 F CONVERTIBLE, these are much more expensive then a coupe.. but…
- Manufacturer
- Reproduction
This is a reproduction patch panel correctly stamped for replacing the shock mounts commonly rusted out rear shock mounting…
The most complete rear deck panel for rebuilding the:
67-9 Camaro or Firebird Coupe or Convertible.
Comes with the main hinges.. deck…
This is the full CONVERTIBLE ONLY rear panel..
HINGED for the trunk lid.. includes mounts and tension…
- Manufacturer
- Reproduction
This shorter rear deck panel goes between the rear quarter panels, is used for repairing rusted deck area's…
- Manufacturer
- Reproduction
This patch is designed for easy installation with original wheel well lip shape the patch is approximately 27 cms by…
- Manufacturer
- Reproduction
These are under the front seat floor pans and form the structural reinforcment to mount the seats runners.
LH is USA…
These are under the front seat floor pans and form the structural reinforcement to mount the seats runners.
LH is USA…
For the repair of the UPPER spring mount area of the subframe .. replacing worn out or rusted mount sections…
These are for 68-69 Firebird & Camaro's... they are the full replacement rear frame rail.. as it would be…
- Manufacturer
- Reproduction
Type One of this panel.. has more going up the sides and the main guts of the floor needed.. with…
- Manufacturer
- Reproduction
Type Two of this panel.. better suited for many rust fixing applications.
This is a factory replicated sectional pressing for the…
This panel is the ideal replacement part if only your rear floor sections under where you put your feet...…
- Manufacturer
- Reproduction
Each 1967-69 panel extends from the rear seat section to the firewall extension upward near the transmission tunnel.
Each…
- Manufacturer
- Reproduction
These bulky new parts are available as either a left or right hand unit and are an excellent alternative to…
- Manufacturer
- Reproduction
These are the front floor sections that run between the flat of the floor pan to the vertical flat of…
- Manufacturer
- Reproduction
This is what the roof gutter mold clips onto.. this is the metal gutter..
It is the…
This is the latest good revised tooling cowl panel as shown for the 1969 F body.
It is pressed/made…
- Manufacturer
- Reproduction
Its the upper exterior panel that needs that is the upper cowl panel. where the vents are.
This panel takes the…
- Manufacturer
- Reproduction
The 1969 only in PAIR SETS of trunk/boot floor re-inforcements were originally welded under the trunk floor to add support…
- Manufacturer
- Reproduction
The ia a SINGLEunder trunk/boot floor re-inforcements were originally welded under the trunk floor to add support to the pressed…
- Manufacturer
- Reproduction
Displaying 1 to 30 (of 38 products)