This is the lower front section of the rear 1/4 panel. Precision stamped panel ready for fitment.
Comes in any colour…
This is a NEW retooled panel set that comes with the inner support brace section as well.
Made for the 67-8…
This is a run out of a of single skin front patch panel ..ONE ONLY..
USA Passenger Side only …
This Rear of Rear patch is designed for easy installation with original wheel well lip shape.
The metal correctly shaped patch…
- Manufacturer
- Reproduction
The lower rear section of each front mudguard / fender is reproduced here enabling easier cut & replace restoration…
- Manufacturer
- Reproduction
This 2 piece lower 69 Camaro quarter repair kit is a well priced alternative to a full quarter…
This patch is designed for easy installation with original wheel well lip shape the patch is approximately 27 cms by…
- Manufacturer
- Reproduction
Rusty or corroded trays are common after 30 odd years of use.. these are perfectly pressed and easy to fit.
Correct…
- Manufacturer
- OER
The ia a SINGLEunder trunk/boot floor re-inforcements were originally welded under the trunk floor to add support to the pressed…
- Manufacturer
- Reproduction
The 1969 only in PAIR SETS of trunk/boot floor re-inforcements were originally welded under the trunk floor to add support…
- Manufacturer
- Reproduction
Its the upper exterior panel that needs that is the upper cowl panel. where the vents are.
This panel takes the…
- Manufacturer
- Reproduction
This is the latest good revised tooling cowl panel as shown for the 1969 F body.
It is pressed/made…
- Manufacturer
- Reproduction
This is what the roof gutter mold clips onto.. this is the metal gutter..
It is the…
These are the front floor sections that run between the flat of the floor pan to the vertical flat of…
- Manufacturer
- Reproduction
These bulky new parts are available as either a left or right hand unit and are an excellent alternative to…
- Manufacturer
- Reproduction
Each 1967-69 panel extends from the rear seat section to the firewall extension upward near the transmission tunnel.
Each…
- Manufacturer
- Reproduction
This panel is the ideal replacement part if only your rear floor sections under where you put your feet...…
- Manufacturer
- Reproduction
Type One of this panel.. has more going up the sides and the main guts of the floor needed.. with…
- Manufacturer
- Reproduction
Type Two of this panel.. better suited for many rust fixing applications.
This is a factory replicated sectional pressing for the…
These are for 68-69 Firebird & Camaro's... they are the full replacement rear frame rail.. as it would be…
- Manufacturer
- Reproduction
For the repair of the UPPER spring mount area of the subframe .. replacing worn out or rusted mount sections…
These are under the front seat floor pans and form the structural reinforcement to mount the seats runners.
LH is USA…
These are under the front seat floor pans and form the structural reinforcment to mount the seats runners.
LH is USA…
This patch is designed for easy installation with original wheel well lip shape the patch is approximately 27 cms by…
- Manufacturer
- Reproduction
This shorter rear deck panel goes between the rear quarter panels, is used for repairing rusted deck area's…
- Manufacturer
- Reproduction
This is the full CONVERTIBLE ONLY rear panel..
HINGED for the trunk lid.. includes mounts and tension…
- Manufacturer
- Reproduction
The most complete rear deck panel for rebuilding the:
67-9 Camaro or Firebird Coupe or Convertible.
Comes with the main hinges.. deck…
This is a reproduction patch panel correctly stamped for replacing the shock mounts commonly rusted out rear shock mounting…
New Steel INNER rocker panels for the 67-9 F CONVERTIBLE, these are much more expensive then a coupe.. but…
- Manufacturer
- Reproduction
This is the factory style pressing of the outer rocker panel for replacement use on either LH or RHS as…
- Manufacturer
- Reproduction
Displaying 1 to 30 (of 38 products)