This is just to show you the RANGE for 1st Gen Camaro restorers.. the different headlamp housings.. more then most…
Front adjuster screws and bumpers to adjust your bonnet.
Includes:
2 screws with nuts
2 rubber bumpers.
…
Stop Rubber (x 1)
. These rubbers mount on the inside lip of your guards in the engine bay area.…
These were /are the best of the two types affordable types commonly available .. & cost a little…
- Manufacturer
- Reproduction
Stopper Rubbers. These rubbers go over your bonnet stopper nuts and are usually fairly worn out with age.
Replace then…
A pair of screw & nut based .. rubber capped bonnet height adjusters & stops as shown.
Supplied as a pair…
- Manufacturer
- OER
This is a exact copy of the long gone 68 Camaro Yenko Fibreglass 427 Hood, produced during the height of…
- Manufacturer
- OER
These are better 2" CI hoods.. better tighter pressed.. aka Q1.. Quality 1st..... good curve tensions in production…
There is several pressings (2017) of the 67- 69 Camaro Cowl Induction Hood.. the full metal 2" Cowl Induction…
- Manufacturer
- Reproduction
These are a good all STEEL fully pressed USA Induction hood for 67-69 Camaro.
These are METAL.
The normal hood is…
Newer pressing 67-9 Camaro CI hood.. with smoother rounded nose and hump as shown... they look GREAT.
This is a…
This is Good value set up of evenly pressured hood hinges for the cars listed.
Good product. up against…
New deep chrome Billet hood hinge set as shown with heavy duty struts.
Delivery is also covered…
A pair of correctly reproduced hood hinge spring set for the 67-9
…
This is Good value up against the GM hinges... BUT... be aware these are a bit lighter then the originals…
- Manufacturer
- Reproduction
Aftermarket type fastening Kit of 20 clips
This is a simple functional kit of he round items but the do the…
67-9 Camaro with Cowl Induction - Molded Precise Pad.
... reproduction of the original item that will help prolong the…
67-9 Camaro with / Cowl Induction
Standard shaped pad. NOT molded.
... reproduction of the original item that will help…
1967-69 Camaro Standard and SS.
Reproduction of the original item that will help prolong the life of the paintwork on your…
1967 & 68 Standard, SS & RS Hood latch Catch Support..... This support bracket will attatch as original and…
- Manufacturer
- Reproduction
1969 Camaro Standard, SS & RS Hood latch Catch Support.....
This support bracket will attatch as original and is reproduced in…
- Manufacturer
- Reproduction
Standard & SS 1967 Camaros (NOT RS & NOT for the Firebird Series.
Be aware there is a cheaper…
- Manufacturer
- Reproduction
1967-68 Rally Sport Latch for those years only.
This hood latch mechanism is an exact reproduction of the original item.
GM Approved…
- Manufacturer
- OER
New Steele reproduction hood latch for the NON-RS series 68 Camaro.
Excellent exact copy of a often twisted up or…
- Manufacturer
- Reproduction
Correct Heavy Duty steel hood release assembly for the 69 Camaro Std, SS & RS... assembled ready to install.
Cheaper version…
Ornament Gaskets roll tape.
These gaskets stop the moisture entering under your hood louvers which could lead to paint and body…
Molded set of hood louver gaskets as shown for the 67 Camaro & 68-74 Nova.
Supplied as pair sets as shown.
USA…
1967 Camaro hood ornament set.
These quality reproduction hood louvers are only sold as a pair.
The hood louver gaskets are also…
- Manufacturer
- OER
The hood louvers are used on all SS-350 and SS-396 Camaros & includes the correct satin black backing plate, the…
- Manufacturer
- Reproduction
This is a exact copy of the long hood scoop pressing with a side flare of around 2…
Displaying 31 to 60 (of 85 products)