Originally the converibles had this stamped metal filler panel in the inside rear behind the armrest panel. Many went missing…
For the 67-69 Camaro Firebird TA series.
Not known unless your restoring one.. but sits between the lock pillar and convertible…
These are correctly metal backed with the seal molded on. Prevents water drainage to the rear body & boot…
Convertible underside brace.
You get a pair. -
Also available as an individual unit on request for about 1/2 price etc.…
- Manufacturer
- Reproduction
Underside Brace for the convertible 67-69 F.
Oversize.. too large for Post.…
- Manufacturer
- Reproduction
These keep the chrome moulding attached to the body. Set of 10 is used to replace all.
This IS a set…
- Manufacturer
- OER
This is a upgraded design of the previously fairly week replacement that was around.
It is designed to keep…
- Manufacturer
- Reproduction
Using a underside reinforcement for the body sag and stiffener on the 1st gen Camaro & Firebird is a Major…
These are brand new Convertible body shells. It's fitted with doors & boot lid as shown.
Price is Ex Wollongong NSW…
Brand New convertible top FRONT header bow.. for the 67-69 Camaro & Firebird.
NOT stocked normally a 10-20 day…
- Manufacturer
- Reproduction
These Chrome finished moulds go across the windscreen top. supplied as LH & RH pairs, joining in the center, attaching…
- Manufacturer
- OER
These are a pair of correct Brushed Chrome finished moulds go across the windscreen top. supplied as LH & RH…
- Manufacturer
- OER
This seal installs on the outer windscreen pillar post and is a high quality reproduction of the original item.…
- Manufacturer
- Metro Rubber
MASSIVE USA price rises on trim parts in 2022.
In the market place there are a…
- Manufacturer
- Reproduction
MASSIVE USA price rises on trim parts in 2022.
In the market place there are…
- Manufacturer
- Reproduction
Full set of 16 clips and retainers to mount the Firebird & Camaro to the cover boot over the well…
- Manufacturer
- OER
There is a few varieties of these.. and the quality sticks out like .. yer.. .
…
- Manufacturer
- PUI
On the exterior folding top .. these dress the end of the bows externally where fitted .. or repaced where…
- Manufacturer
- Inline Tube
Each cabble has a spring loaded end that tensions the collapsing frame as its retracted.
Cables rust up over the years…
- Manufacturer
- OER
This is the two small bumper stoppers that screw into the frame rails to cushion the end folding. Two…
July 2022 THESE are now discontinued by the Manufacturer.. while not all is lost.. supply is crippled. IF…
This goes across the metal convertible top header bow, enough to dress up and protect your fingers from the metal…
Complete hose kit with brase ends and fitting.
THIS IS A PAIR SET.
Each hose is specifically power top with…
Excellent complete latch assemblies for BOTH sides of the convertible top frame that latches the frame to the sunvisor brackets.
Supplied…
- Manufacturer
- Reproduction
Replacement Convertible Top Piston BOLTS: 67-69 Camaro Firebird (PR) Plus GM A body ie Chevelle, GTO Cutlass & full Size…
For the 67-9 Firebird & Camaro Convertible.. the Convertible top pivot bolt and washer renewal hardward kit... for the…
Small bump stop the convertible top pumps legs require to help prevent movement and insulator from vibration damage.
Some cars used…
A brand new converible top pump - looks slightly different then the original body from GM in the 1960s-…
This is a close as you will get to a perfect gutter for the 67-69 series. Its ABS molded one…
Hydraulic Rams are on each side of the convertible top frame and physically lift the frame up, these are…
Displaying 1 to 30 (of 53 products)