Remember.. Pontiac is different to a Chevy.. .. the main immediate thing is the Dissy rotates…
Factory exhaust manifold bolt and bolt/studs in a 6 pack as shown.…
Pontiac V8 287, 301 (not turbo) 316, 326, 350, 370, 389, 400, 421, 428 & 455 Street…
Full set of PONTIAC V8 67-81 Cam bearings.
326, 350, 400, 421, 455…
This is a specific cam for the Pontiac 301 & 301 Turbo...
Spec's for the record are 256/256. 349/349,…
- Manufacturer
- Mellings (USA)
Uncollected order.. big loss..your gain if you can use it.. its for the Pontiac 6 cyl 4.1 . known…
Dip Stick TUBE: Pontiac 665-68 - IN SUMP 39 degrees
This is for the USA made Pontiac V8.. ie 326, 350, 400,…
Dip Stick TUBE: Pontiac 69-73 - IN SUMP 52 degrees
There is another one that is lesser angled at 39 degrees.
THIS…
This is USA GM's specific engine component assembly lube.. nearly 500 mil bottle..and provides outstanding protection against run-in wear…
- Manufacturer
- General Motors
Simple quaity parts in a kit from once sizes are known.. You can buy cheaper and most are price line…
Brand new kit of 6 correct flexplate to crank bolts as shown.
Fits Pontiac /Olds/Buick Engines 64-76 era at least.…
These are a performance USA Made HAYES Pontiac Billet Steel flywheel for the manual trans PONTIAC V8.. 64-79.
326
350
389
400
428
455
…
Intake for the 403 Olds as found on 77-79 Firebird TA.s..
Image is correct. Comes with a tube of…
This is the full gasket kit for all Pontiac 350 400 & 455 (non Super Duty) V8 engines from…
Brand new set of 8 x 3/8" Pontiac V8 Head guide plates for the Pontiac V8.
…
This is the round harmonic balancer seal in the timing cover for the vehicles listed below.. particularly
Pontiac V8's from 65…
Pontiac V8 Head bolt set for the Edelbrock Alloy Heads ONLY..... contains the complete set of high quality hardened…
- Manufacturer
- Edelbrock
1967-79 Pontiac Factory D Port Cylinder Head Bolts Bolt Set,
Pontiac V8 .. 301, 350, 400, 421, 455 Ram Air 3…
- Manufacturer
- Inline Tube
Correct Enginetech Tensile Chevy small block engine bolts...
- 1955-2000.
Enginetech Head Bolts are made to…
Various factory dupicate PONTIAC V8 head studs and bolts as shown.
Choose as needed.
Supplied each
(A) Bolt Head STUD , 1/2"-13…
New Set of 16 engine lifter for the403 Olds V8 series.. as found in the 77-79 Firebird Trans Am series... …
New Set of 16 engine lifter for the Pontiac V8 series.. real Pontiac.. not chev.. they are different.
This set…
- Manufacturer
- Federal Mogul
Small block Chevy Oil pump with 5/8" inlet:
Fits: 1957-85 era Camaro, Firebird w/Chev V8), Belair, Impala, Chevelle, Nova…
- Manufacturer
- Mellings (USA)
Oil Pump Drive shaft
Fits…
New main shaft between the dissy and the oil pump.. its what drives the oil pump on the Pontiac…
New Oil pump drive shaft for the SB Chevy.. widely used for over 40 years of SB Chevy.…
New U.S. Produced correct pressure Engine oil pump as shown, only for the 77-81 301 V8 Carby & 301…
- Manufacturer
- Reproduction
Brand New made Olds 403 Oil Pump for the Oldsmobile V8's in 77-79 Firebird & Trans Am.
Choose…
American made Sealed Power / Mellings oil pump for the 301-350-400-455 Pontiac V8. NOTE.. that some 455's…
- Manufacturer
- Federal Mogul
This is the correct push rod for the 403 olds 6.6 lt as found in 77-80 Firebirds and Trans Am.…
Displaying 1 to 30 (of 55 products)