1964 Chev Impala SS - Specifically.. UPPER. . with Clips
Delivery is covered for supply within Australia, NO POST or COD. NT & Regional WA Additional.…
This is a 30 part kit.
Kit includes the housings.. AS LISTED.
6 x New brake lense metal housings
4 x Brake lenses
2 x REVERSE Lenses
6 x rear of housing rubber insulation gaskets.
6 x lens to housing gaskets
6 x Chrome trim set
All new. Delivery is covered on this too when ordered and paid online
for supply within Australia.…
A one year only grille emblem for the 64 Chevy full size.. be it assembled in Canada, Australia NZ or South Africa or the USA.. same riveted emblem.
Really nice part ... if you like nice parts...…
VERY VERY nice part.
New boot lid chrome outer housing with original reproduction insert.
Really nice part for the 1964 Chevy Full Size…
Just the multi coloured plastic insert that goes inside the chrome frame on the boot lid as shown.…
This is the extended sectional rear 1/4 face Skin only.. not a full 1/4 or a full skin.. just as show... its a major section of the two door 1/4 skin.
Length is 66 inches
Height is 23" Inches.
LHS is USA Drivers Side.
...............................................................................................................
Full 1/4's are not made at the time of listing for 4 door sedans, wagons or 4 door pillarless sedans.. just coupes & convertibles.
THESE ARE A BIG PANEL TO SHIP AND MUST BE DONE WITH ABSOLUTE CARE.
FYI: A full length face skin for a 2 door.. that could be partially used to help the restoration of a 4 door or wagon IS also available being longer then this one.... but this is a section of that face skin..
** Alternative.. Rear of the wheel arch 40" sections also available.. listed separately.
Special order only normally.. allow 10-16 days on average for supply... order cut off is 2pm Tuesday for normally the next weeks Wednesday arrival in our Wollongong Warehouse.
Delivery is additional on this part.. but from $55 & up nation wide for one or a pair pro-rata ex Wollongong NSW.…
New Reproduction boot /trunk lid for the IMPALA series with FOUR LAMPS.. not two like the Belair. this is NOT an Belair trunk lid..
Good fit from experience, good reproduction panel... without rust...!
This is a special order part not regularly stocked. It take 2-3 weeks to come via our air cargo every 14 days.(air freighted economically) .. and requires a firm order.
Local Australian Delivery is additional cost on this item & is by Courier. ....this is too big for the post COD. so no COD deliveries.
IT IS A BIG BULKY HEAVILY PACKAGED consignment…
This is the chrome spear ornament on the center of the 64 Chevy Hood.
Delivery covered when ordered and paid online for supply within Australia.…
New Reproduction set of headlamp moldings the actually fit, your getting a pair here for the restoration of the front end.
Delivery is covered when paid & ordered on line for supply within Australia.…
LONG time needed and now you can finally get one.. the GM Restoration Parts approved Hood is an excellent pressing.. worth the time to consider the alternatives also due to the expense but not often you can get a perfect panel for this series car..
Note: This is the Impala hood and has the holes down the center for the hood "spear" molding to be fastened to. The Belair hood did not have the hood spear as factory.. but the hoods the same otherwise and you can if you want.. buy the spear and fit it.
GM Restoration Parts Approved.
STOCK ITEM normally but do sell out... 3 week replenishment time.
Delivery is available.. but we also need to advise you either to pick it up or have us Wood Create Frame the hood.. its takes an average of 32 mtrs of timber and about 3 hrs to do... cost is $132 for that, plus freight plus insurance @ $4 /$100 value.
…
Correct reproducton lower molding...for the 64 Impala or Belair.. simple as that..
GM Restoration Parts Approved.
This molding is about 2 metres long and required tubing . (ex bunnings drain PVC pipe) and oversize delivery we cover the tubing .. you keep it.. the freight is additional subject on your location but normally realistic, way too big for post..
Realistically you can get one out of the USA cheaper but its will end up either bent or costing more.. no simple cheap way with this.
…
The grille is fully assembled.. it has the headlamp housings & brackets.. it is a complete unit.
Perfect reproduction.
You can also have just the grille face panel if you only need that .. which means you'll need to replace and refit all the metal riveted supports to the grille to fit it... for around $200 cheaper (call if thats what you need - but will involve considerable reconstruction etc.)
…
If only a few needed this is probably the neatest way to restore the rear of the 64's Brake or Reverse lamp housings.
If your needing a full set.. there is also a full kit of housings and lenses with gaskets but a few hundred more.
This is for ONE as shown.…
Brand new LH or RH headlamp bezels for the 64 Chevy Impala or Belair.
Cheaper as this set of 4 if required.…
Brand new LH or RH headlamp bezels for the 64 Chevy Impala or Belair.
GM Restoration Parts Approved.
Four needed Per car.. one for each headlamp.
Supply is for ONE unit.. order two if doing both sides.
…
**... get one while you can if still needed.. been globally gone for too long..
Bonnet front lip molding as shown with the emblem insert.
Really - REALLY nice part.
Normally stocked subject to NOTE above.
Delivery covered on this also in Australia when ordered and paid online.
…
New detailed park lamp housing with hardware as shown.
fits LH or RH.
Sold EACH.…
For the 4 door Sedan and Pillarless sedan.. the full Impala side molding kit. Kit does not include clips or retainers.
Special order only.. allow 2 weeks average for supply.
Delivery covered within Australia when ordered and paid on line.
Set includes:
LH/RH upper fender moldings
LH/RH lower fender moldings
LH/RH upper front door moldings
LH/RH lower front door moldings
LH/RH upper rear door moldings
LH/RH lower rear door moldings
LH/RH upper quarter panel molding
LH/RH lower quarter panel molding
LH/RH rear quarter "C" moldings
…
Full Side reproduction of the body side moldings for 1964 Impala 2 door models, (Not SS) with off white accents.
New Clip kit included
Includes:
Left and right hand upper fender moldings
Left and right hand lower fender moldings
Left and right hand upper door moldings
Left and right hand lower door moldings
Left and right hand upper quarter panel molding
Left and right hand lower quarter panel molding
Left and right hand rear quarter "C" moldings
Side molding clip kit
This is a one year one model of one 2 door coupe body and rare it's realistically a Special order only kit.. allow 2-3 weeks.
Delivery covered in Australia wide when ordered and paid online.
…
Brand new front mudguard molding.. for the Impala. as shown.
Supplied individually.
LH is USA Drivers Side.…
Brand New production front fender eybrow molds for the 64 Chevy series.
Supplied as a matched pair.
Supplied with a clip kit too.
…
Full rear window molding kit for the 64-65 A body coupe..
Brand new parts.
Chevelle
GTO / Lemans
Delivery is also covered when ordered and paid online for supply within Australia. …
These are the PAIR of seals between the door glass window and the rear side window.. slides into a chrome channel has a moulded finished end.
There is a difference between Convertible and coupe....
These have a steel core to keep them straight.…
These fit onto the center pillar caps and act as the trims final edge dress.
Left & Right handed unit supplied as a pair..
Excellent repro.
Supplied in pair sets only.
…
1964-67 GM “A”-body Rear Frame Crossmember (goes side to side at rear of frame)
GM A -bodies are: Chevelle / El Camino, Tempest / LeMans / GTO, F-85 / Cutlass / 442, Special / Skylark / GS
Special order only.. allow 3 weeks.…
64-69 GTO - LeMans, Tempest /Chevelle Malibu/ Olds Cutlass GM-body Frame Crossmember
Choose front or center.
Special order only .. allow 3 weeks.…
Brand New pair front park lamp lenses in Amber or clear.
The Majority of export Canadian, NZ built or Australian built used clear..
Supplied as a pair set.
…
Brand new perfect clean clear reverse lens set for the 65 Full Size Chev.
This is a pair set.
For some.. this is a way of making a AMBER turn signal needed for various states or types of rego.. simply use a LED Bulb in place of a clear for that application.. otherwise.. its the factory reverse lens set as shown.…
This is ONE lens and bezel set for either side for the full size Chevy Impala Belair series.…
For fixing rusted or damaged tail panel just below the boot lid ... for the 65 ONLY IMPALA series. but fits all bodies.
Delivery additional.- Stock panel normally…
Displaying 241 to 270 (of 6179 products)